Creations, construction techniques, and news from the world of plastic toys
Moderators: Dr. X, fredde
1 question: does heat give minifigs cracked arms and legs? ( i don't mean fire i mean stuff like underfloor heating)
You want those Rebels dead? You are a penis compared to how much I want those Rebels dead!
- Posts: 756
- Joined: Sat Jul 20, 2013 9:17 am
- Location: Switzerland
I highly doubt the heating in the house would interfere with what you put on the floor. Even then, I'm almost positive that if anything caused your lego's to crack it would be the cold.
Then again I failed science so you should probably get colette or something he knows alot
of stupid shit
- Who watches the overwatch while the overwatch watches over the watchers of the overwatch?
- Posts: 971
- Joined: Sat Oct 13, 2012 3:31 pm
Rapid heating and cooling can make some materials brittle, but generally you'd need to heat a substance to the point that it's nearly melted in order to risk damage from cooling it back down. So unless your floor gets hot enough to melt plastic, you should be fine (and if it does, you have bigger problems than a few melted minifigs).
"There's suspension of disbelief and then there's insulting my fucking intelligence"
- Posts: 517
- Joined: Tue May 01, 2012 5:52 pm
- Location: Limbo
Maybe if you put them right on the heater. But why would you do that?
Are you sure it's not your dog again?
Give a minifig an inch, and he'll murder for a mile.
- Posts: 669
- Joined: Wed Jul 14, 2010 3:01 am
Um... heat usually doesn't, but every now and then Lego gets a shipment of plastic pellets with some kind of impurity in them that causes the plastic to develop cracks over time during normal use - the cracks are usually along seam lines, but sometimes right in the middle of a flat surface. Several of the original Pirate sets that I got when I was a kid developed cracks like those. Doesn't happen often, but it does happen. Could also be from the plastic cooling too quickly during casting so it doesn't "meld" properly...
- Posts: 173
- Joined: Thu Jul 23, 2009 9:29 pm
- Location: Wandering through Mirial's Rock...
Scribonius wrote: it doesn't "meld" properly...
That's what Sarek said,
when talking about his overly emotional, halfbreed son.
- Posts: 4793
- Joined: Sun Dec 30, 2007 4:41 pm
- Location: Boston
Could also be from the plastic cooling too quickly during casting so it doesn't "meld" properly...
Yup, that's what happened to the majority of lime colored bonkle connector pieces in 2007. Those things were brittle as shit, cracking and breaking after the first attaching/detaching.
- balls just have this nasty tendency to wear out over time
- Posts: 4155
- Joined: Fri Jul 24, 2009 6:22 am
- Location: Hüngäry
Unless you leave legos in the trunk of a car with your dead bodies during the middle of summer, heat wont ruin your legos.
my old sig
WARNING: Posts in forum may have been edited by forum
- Posts: 1508
- Joined: Sun Oct 04, 2009 7:09 pm
- Location: planet express
Don't put lego on the floor. Haven't you ever in your life stepped on one?
"You ain't my friend, palooka." - Vincent Vega
- Posts: 164
- Joined: Mon Feb 18, 2013 3:11 am
- Location: Over there.
I think this is a question I could answer correctly.
As much as I know thermal cracking of ABS could occur right after the manufacture process when hot plastic cooled down but reheating could not lead the parts to crack.
- Supercharged Tank
- Posts: 242
- Joined: Sat May 05, 2012 2:50 pm
Return to Bricks
Who is online
Users browsing this forum: Insert_blank, Silent-sigfig and 1 guest